I just had a local clutch and brake business remake my clutch cable. Looks like they reused the adjustment mechanism and the nylon cable ends from my old cable..and used a new inner /outer cable.
Cost $130.00 which sounds a bit expensive..but the alternative is a piece of rope through a hole in the floor attached to the throwout arm.
Remanufactured Clutch Cables
- Sigmaproject
- Posts: 1143
- Joined: Sun Mar 22, 2009 7:11 am
- Location: Maitland NSW
Re: Remanufactured Clutch Cables
Pretty sure Flexible Drive Agencies also make them for around 85.00
- LukeAussie
- Posts: 353
- Joined: Fri May 18, 2012 9:55 am
- Location: Adelaide
Re: Remanufactured Clutch Cables
Hi guys, yeah, Flexible Drive Agencies do this kind of thing (including re-working old gear if new ones can't be found), and also do speedo cables, accelerator cables, etc. Pretty sure they're in every state too...
- Sigmaproject
- Posts: 1143
- Joined: Sun Mar 22, 2009 7:11 am
- Location: Maitland NSW
Re: Remanufactured Clutch Cables
I probably could have found cheaper options..but these guys were 5 minutes from home, and I had it back in an hour.
Re: Remanufactured Clutch Cables
G'day Sigmaproject.
I've got a couple of new genuine cables with the screw adjust I could part with if you want a spare.
I've got a couple of new genuine cables with the screw adjust I could part with if you want a spare.
"Just remember, if you aren't forced induced, then you aren't SH#T"
GH Sigma Turbo no. 047
Leyland P76 V8 (next for resto)
Jaguar XJ8 Sport (british racing green of course)
Land Rover Discovery II V8 (the daily drive)
GH Sigma Turbo no. 047
Leyland P76 V8 (next for resto)
Jaguar XJ8 Sport (british racing green of course)
Land Rover Discovery II V8 (the daily drive)
- Sigmaproject
- Posts: 1143
- Joined: Sun Mar 22, 2009 7:11 am
- Location: Maitland NSW
Re: Remanufactured Clutch Cables
mate..if it is approx 1350mm tip to tip I will take one from you. This one I had made is actually my spare. I had a new cable I bought off ebay years ago to fit a GN Sigma and unfortunately it is about 50mm too long.
So I had to fit a 50mm spacers were it goes through the firewall to shorten the inner. Works OK ..but looks a bit dodgy. So if your cable is the right length I will take one.
PM me with your price.
So I had to fit a 50mm spacers were it goes through the firewall to shorten the inner. Works OK ..but looks a bit dodgy. So if your cable is the right length I will take one.
PM me with your price.
- amgis_obrut
- Posts: 1742
- Joined: Wed Mar 18, 2009 6:26 pm
- Location: Orient Point NSW
Re: Remanufactured Clutch Cables
I need to check if I have any NOS cables at my other shed, I had a few hundred of them and was selling them for $30 each
GH Sigma, 16" Mesh wheels, sports steering wheel and a V8 exhaust
- Sigmaproject
- Posts: 1143
- Joined: Sun Mar 22, 2009 7:11 am
- Location: Maitland NSW
Re: Remanufactured Clutch Cables
The cable I am after is part #4158964
That is the GN part #. Maybe previous models have the same cable with a different part #. Who knows.
I'm guessing that the cable I bought that was too long was from a Triton or a Pajero (thats if they have cable clutches )
That is the GN part #. Maybe previous models have the same cable with a different part #. Who knows.
I'm guessing that the cable I bought that was too long was from a Triton or a Pajero (thats if they have cable clutches )