motor swap and cant get it runing plz help

This section is for talk about anything to do with everything in the engine bay.
Post Reply
armor117
Posts: 50
Joined: Sun Apr 15, 2012 6:39 pm

motor swap and cant get it runing plz help

Post by armor117 »

i just swap the motor in my ge from 2l to a 2.6 out of a gj and wire it up am 90% such the wiring is rigth but there no spark what could it be i left the coil from my 2l in there because it was still good
BAD-SIG
Posts: 520
Joined: Tue Mar 24, 2009 6:05 am
Location: Ballarat, VIC
Contact:

Re: motor swap and cant get it runing plz help

Post by BAD-SIG »

It might depend on which distributor you are using. Does it have a little ignition box bolted to it or does it look the same as the original Astron 2000 one? The later model Astron engines had a different arrangement for the distributor and ignition module.
Please click below to visit my blog dedicated to my GE Sigma SE:
http://www.galant-sigma.com

Please click below to visit my cardomain website dedicated to my GE Sigma SE:
http://www.cardomain.com/ride/293989

Image
armor117
Posts: 50
Joined: Sun Apr 15, 2012 6:39 pm

Re: motor swap and cant get it runing plz help

Post by armor117 »

it got a big box cased to the distributor i think the the pick up so i when and got a o24 module and wire it up with that still no spark iam think i mite just go to the wreckers and get a distributor from a magna and see if that works
BAD-SIG
Posts: 520
Joined: Tue Mar 24, 2009 6:05 am
Location: Ballarat, VIC
Contact:

Re: motor swap and cant get it runing plz help

Post by BAD-SIG »

This means then that you got a different setup than the original one. I encountered this same problem when I fitted a hybrid GN Sigma and Magna 2.6 engine into my GE Sigma. The GE uses an ignition module sepparate to the distributor and the newer GK onwards Astrons have the ignition module bolted to the distributor. This meas you have to rewire the ignition. You'll notice the GE has multiple wires going into the bottom of the Bosch ignition module and the GK onwards dizzy only has two wires going into it. I cant remember exactly which wires i cut and which I used, but I had to have the wiring diagram from both the GE and the GK Sigmas so I could work out what goes where. Once wiring was done, the engine fired up straight away!
Please click below to visit my blog dedicated to my GE Sigma SE:
http://www.galant-sigma.com

Please click below to visit my cardomain website dedicated to my GE Sigma SE:
http://www.cardomain.com/ride/293989

Image
GB_BB4C
Posts: 932
Joined: Fri Mar 20, 2009 9:37 am
Location: Adelaide, SA

Re: motor swap and cant get it runing plz help

Post by GB_BB4C »

Or put the old dizzy from the 2lt in, no cutting wires etc...
2* 73 A53 16L Dodge Colt (Plymouth Cricket), 2* 73 GB Galant Sedan's, 1* 74 GB Galant Sedan, 1* 76 VK Valiant Regal,
1* 79 GE SE Sigma Sedan, 1* 81 GH Sigma PWS, 1* 84 GK Sigma SE, 1* 85 GK Sigma GL - Replacing the 84 GK SE, 1* 91 GTO - FOR SALE

Image
armor117
Posts: 50
Joined: Sun Apr 15, 2012 6:39 pm

Re: motor swap and cant get it runing plz help

Post by armor117 »

i put the 2l distributor in turn the key and bang off she when thz guys heaps i just have to get a timeing ligth tommow and it will be sweet so happy :D its runing you guys are life savers
BAD-SIG
Posts: 520
Joined: Tue Mar 24, 2009 6:05 am
Location: Ballarat, VIC
Contact:

Re: motor swap and cant get it runing plz help

Post by BAD-SIG »

Make sure you take the dizzy to a specialist to get it regraphed to make the most of your 2.6 :)
Please click below to visit my blog dedicated to my GE Sigma SE:
http://www.galant-sigma.com

Please click below to visit my cardomain website dedicated to my GE Sigma SE:
http://www.cardomain.com/ride/293989

Image
armor117
Posts: 50
Joined: Sun Apr 15, 2012 6:39 pm

Re: motor swap and cant get it runing plz help

Post by armor117 »

thz for telling me that i didn't know you had to re-graphed the distributor ill make a call Monday and see if any one in town does it ill have to wait a little longer to drive it dam
BAD-SIG
Posts: 520
Joined: Tue Mar 24, 2009 6:05 am
Location: Ballarat, VIC
Contact:

Re: motor swap and cant get it runing plz help

Post by BAD-SIG »

You don't have to, its better to though
Please click below to visit my blog dedicated to my GE Sigma SE:
http://www.galant-sigma.com

Please click below to visit my cardomain website dedicated to my GE Sigma SE:
http://www.cardomain.com/ride/293989

Image
armor117
Posts: 50
Joined: Sun Apr 15, 2012 6:39 pm

Re: motor swap and cant get it runing plz help

Post by armor117 »

thz heaps for the information i would be lost if not for people like you
Post Reply