Has anybody come across gasket kits for the twin cam? Ours is nearly ready, we just need a few 'odds and ends'.
Any help would be appreciated,
Dan
4G32 Twin Cam
4G32 Twin Cam
2 x LA 2 Dr
3 x LA 4 Dr
1 x LB 4 Dr
2 x 4G32 Twin Cams
3 x LA 4 Dr
1 x LB 4 Dr
2 x 4G32 Twin Cams
-
Rally_2.6LC
- Posts: 954
- Joined: Sun Mar 22, 2009 10:59 am
- Location: Either under a car, on the computer or in bed...around Ryde
Re: 4G32 Twin Cam
Hoonboy use to have one, but its extremely hard to come by these now.
Ive never seen a listing in Aus for them, maybe try Japan.
Unforutnatly these engines were few and far between.
Cheers Matt
Ive never seen a listing in Aus for them, maybe try Japan.
Unforutnatly these engines were few and far between.
Cheers Matt
'75 GC daily (slowly dying)
'80 LC 2.6L rally car (generally something broken until 2 weeks before an event)
'71 GA 2.6 Turbo project (i only wanted the diff and got another project)
^This side up^
Formely "Matt"
'80 LC 2.6L rally car (generally something broken until 2 weeks before an event)
'71 GA 2.6 Turbo project (i only wanted the diff and got another project)
^This side up^
Formely "Matt"
Re: 4G32 Twin Cam
If this post is about getting a gasket for a twincam 4g32 then it might be best to take a look at hoonboys thread on performance forums. On his post on the 25/5/07 he mentions about using a 4g37 head gasket. The rest of the bottom end might be the same as a 4g32 but i'm not sure.
http://board.performanceforums.com/foru ... 1#poststop
If you are actually trying to find a 4g32 DOHC then good luck as i have only seen 4 in australia over the last 5 years. And only 2 of them were for sale on ebay for a grand or 3
http://board.performanceforums.com/foru ... 1#poststop
If you are actually trying to find a 4g32 DOHC then good luck as i have only seen 4 in australia over the last 5 years. And only 2 of them were for sale on ebay for a grand or 3
'72 GB Galant Sedan nanna spec daily
'85 GN Sigma Wagon 4g63 SOHC Turbo almost ready for the road
'74 GC Galant Coupe long term project
'85 GN Sigma Wagon 4g63 SOHC Turbo almost ready for the road
'74 GC Galant Coupe long term project
Re: 4G32 Twin Cam
Woops,
I have a twin cam 4G32. I thought I'd ask about a gasket kit as it'd make life a little easier not to have to have gaskets made. The head gasket is the easy one, there are a few others that are a little tougher.
Dan
I have a twin cam 4G32. I thought I'd ask about a gasket kit as it'd make life a little easier not to have to have gaskets made. The head gasket is the easy one, there are a few others that are a little tougher.
Dan
2 x LA 2 Dr
3 x LA 4 Dr
1 x LB 4 Dr
2 x 4G32 Twin Cams
3 x LA 4 Dr
1 x LB 4 Dr
2 x 4G32 Twin Cams
Re: 4G32 Twin Cam
Head gasket is off the shelf 4G32/37 depending on your bore size, the rest have to be made up, nothing available. The half-moon rubbers at the back of the rocker cover are available from another car, but I can't remember which one.