repro GE-GH dashpads anyone interested?

theozsnowman · Post by **theozsnowman** » Sat Jun 07, 2014 1:27 pm

im considering building a mould to allow me to do up a couple of leather skinned top dash pads to fit my scorpions and to help offset the cost im wondering if anyone else would be interested in them?

Once built they would be skinned in stitched leather or vinyl to suit and match the original

bigfoot · Post by **bigfoot** » Sat Jun 07, 2014 3:37 pm

could be keen on a vinyl one. depending on price/how much it costs to get it this side of the ditch

Post by **Superscan811** » Sat Jun 07, 2014 10:47 pm

Depending on the price, I'd be interested in 2.

Cheers.

theozsnowman · Post by **theozsnowman** » Sun Jun 08, 2014 3:08 pm

yeah price will be determined by the numbers that may be interested as naturally if i can produce more the price can get driven down...

Post by **A112H** » Tue Jun 10, 2014 6:06 am

Dependent on price on look I would want one, maybe two

LukeAussie · Post by **LukeAussie** » Fri Jun 13, 2014 9:34 am

Jason, welcome back!

BIGDAN · Post by **BIGDAN** » Sat Jun 14, 2014 2:47 pm

Depending on price I need 2 ... but 1 extra for a spare ....
:-)

BlueThunder · Post by **BlueThunder** » Sat Jun 14, 2014 7:05 pm

If you could do some LHD LB/LC Lancer Hatchback (Celeste) ones I would take 1 or 2, maybe more...

Oldfart · Post by **Oldfart** » Fri Dec 30, 2016 10:56 am

Was there ever anything further with the dash reproductions?

Post by **A112H** » Sat Dec 31, 2016 11:56 am

As above, still suffering from Scorpion dash over here

Oldfart · Post by **Oldfart** » Sun Jan 01, 2017 11:14 am

Might have to see a decent upholster to make up a new top section

webby · Post by **webby** » Mon Jan 02, 2017 8:33 pm

I'd be keen, depending on price. That's assuming I can make the early dash fit in a GJ, lol

theozsnowman · Post by **theozsnowman** » Wed Jan 25, 2017 6:13 pm

I'm still working on a suitable mould and closed foam base... Looking to get a 3d map done of my good one in a few weeks so I can look to get some inserts done on a cnc...

The internal metal brace and bolt pins is proving to be a bit of a challenge

doofis200 · Post by **doofis200** » Fri Mar 31, 2017 6:15 pm

I would definitely be interested in one, depending on price.

Post by **A112H** » Sat Apr 01, 2017 12:14 pm

Any movement here snowman?

Post by **A112H** » Thu Apr 27, 2017 10:39 am

Getting very close to needing one here.
Any news?

Greenscorp · Post by **Greenscorp** » Wed Jul 26, 2017 10:48 pm

I'm interested in one or two of them depending on the price.

doofis200 · Post by **doofis200** » Sun Dec 17, 2017 5:53 pm

Did anything further end up happening with these?

theozsnowman · Post by **theozsnowman** » Mon Jan 22, 2018 8:33 pm

Sorry still working it out...but my priority has been getting my GH ready to spray.... Been very time poor due to speedway cars and stuff...

Ive made a positive mould but wasnt happy with it so will be doing some more reshaping before trialling some negatives

Sigma-galant.com

repro GE-GH dashpads anyone interested?

repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?

Re: repro GE-GH dashpads anyone interested?