Sigma-galant.com

hi well ive always been into old mitsis now have another 1984 gk se sigma its tidy and low kms so far ive put the pepper pot wheels on a decent stereo and quality alpine speakers still got sub and amp to go in. ive had it tinted wich looks good now. last weekend got a new radiator cap but bout 15min later its over heating dam least wasnt far from home so found the prob hole in manifold thought ill fix the whole lot all in 1 go new recored rad water pump and a nice big 45 mm delortto side draught carb should do the trick for now still got a set of cobra reclining seats to replace the high factory seats and spings and sway bars if any are posible to get i also have fotos will post up soon wen i have it running

Clean sig - keep up the good work.

cheers mate the other pick dnt seem to b up it changed a bit since those fotos the other photos didnt come up of how it is now its wierd

Those links you had didn't lead anywhere? but found those ones; assuming they were what you were after

Neat looking car too

yea mate they are they one the fist few is how i bought it now its go the peppers and tinted alround thanks ive stil got a fair bit to go but it slowly geting there will put up more picks wen finised under the bonet

just thought id show some pics of the old and the new

havent updated for a wile done a bit of work car is now at rpw in perth for 2 half inch exhaust and dyno tune the 45ml delorto and few other litle bits and pieces that didnt had to do hopefully get to pick it up later this week and finaly drive her again cant wait been off the road for bout 2 months and hopefully go and sound beter

so how did it all go, Nate?

We just finished his exhaust tonight with a nice 2 1/2" system with a Lukey Ultra flow rear muffler, magnaflow resonator and a small hotdog in between the two to keep noise at aceptable levels. Sounds nice.

Carburettor has been fixed (Was flooding on the float levels) and car is now running and idling properly.

Just need to sort out the heater hoses and its ready to go onto the dyno and be run up. We will give him a dyno sheet to so he can post it up on the forums. Very neat looking sigma nice to see them again.

awsome guys cant wait to drive it again hope it goes lil beter than standerd

picked up my sigma on friday thanks to rpw u guys have done an awsome job on the exhaust and the tune it runs so much beter. the noise it makes now is realy unique and goes a lot harder than standerd its got 92 at the wheels wich i think is not to bad just from a carb and exhaust. next ill be doin is lowerd springs nolathane bushes and new stickyer tyres for now tho im just goin to enjoy driving it as something more important than cars is happining at this stage in my life

hey guys well been a wile since last update been bizy as hell have been enjoying my driving my car maybe a lil to much now as the cluctch is starting to slip a bit now
so now my plan is to take the motor out in the next few months replace the clutch with heavy duty clutch and lightebd fly weel any recomedations ? as to wich brand is beter also how much is good to take of the fly weel ?
I also have a magna m7 head now so will start cleaning that up is it worth porting and polishing ? or do they flow enough as they are ?
wile the engine is out will clean up the engine bay get a big thermo fan and remove the the factory fan. ill get decent aftermaret cam in the m7 head and will finally be replacing suspension and brakes so i have a bit of work to do but will get there

Hey guys thought I'd give an up date I just finished instlling custom made super low springs in the sig it now sit 105 mm of the ground at the same time replaced some bushes and all new tie rods ball joints and front brakes don't no how to upload fotos from iPad tho

Well got a wheel alignment done to day the front wheels have now got 2.6 deg of neg camber and 0 toe it drives absolutely awsome all I did was turn the strut tops 180 degrees simple will also be getting strut brace as well

Looks great mate, sounds like your doin some great mods! keep us posted!!

Thanks mate ive been meaning to get some photos up yea will do still got few more things to do

Hey guys thought I'd give an update vented front discs and pads all done wen changed new springs and bushes stopps real good now . After market water and oil gauges goin in I have a heap of photos but don't know how up up load with an I pad any help would be cool cheers

Hey guys thought give bit of an update i have found me gsr rear spoiler thatl be goin on when i find a front lip also got some sway bars and new shocks coming and also found this on ebay
http://www.ebay.com.au/itm/MITSUBISHI-S ... 78920?var=

Hey Nato, I am pretty sure that vr4retrofit was in the process of or have made a mold for the front lips. I think this has now been sold to GB_BB4C?? Maybe flick him a PM and see where he is at with the process.
They always seem to be bent and buckled, a fibreglass one would be much nicer, lol

http://i1142.photobucket.com/albums/n61 ... 3952_n.jpg
nathan_white1/Facebook/Mobile%20Uploads/564666_411224495593890_1577472465_n.jpg
<a href="http://s1142.beta.photobucket.com/user/ ... o.jpg.html" target="_blank"><img src="http://i1142.photobucket.com/albums/n61 ... 4567_o.jpg" border="0" alt="My mechanical bitches"/></a>
Hope these work

Yea i was in contact with mike few month ago but dnt really know wat happned ill pm him

Hey trying to post some pics up but this stupid ipad wont do it can any one help

Hey just thought id give an update just recently finished installing a 27 mm selby sway bar. the car handles wicked now no more boaty type feel front is realy responsive took them a wile to make but can still get em .

Ive just put in a set of starion front seats in this now bolted straight in sit a bit lower my head was almost touchin the roof so they are heaps more comy will have gsr front and rear lips on in the next few weeks next is sorting an lsd dif ?