Page 1 of 1
GH with a EVO ix 4G63 engine
Posted: Sat Dec 26, 2015 8:33 am
by LSX
Well, I think it's about time I shared some photos. Purchased this a few years ago.
Mods are.
Forged EVO ix mivec motor ported head kelford cams
Motec m130 ecu drive by wire throttle
Mark Williams 9 inch rear end, 40 spline axles aluminium bolt through centre.
I initially had a T56 6 Spd manuel, changed it to a power glide.
Re: GH with a EVO ix 4G63 engine
Posted: Sat Dec 26, 2015 10:03 am
by Scorpma82
Interesting combo.....how easy was it to bolt up the t56?
Any progress pics or details on that?
Re: GH with a EVO ix 4G63 engine
Posted: Sat Dec 26, 2015 11:05 am
by LSX
It was quite easy. Bill Hincher makes a bell housing to suit.
I opted for the short shaft t56 magnum. With very very minimal auto tunnel mods, the box fits in easy.
Re: GH with a EVO ix 4G63 engine
Posted: Sat Dec 26, 2015 11:11 am
by LSX
Wide block/t56
EVO/t56
EVO/GM POWERGLIDE
Re: GH with a EVO ix 4G63 engine
Posted: Sat Dec 26, 2015 3:04 pm
by stealth
Are you going to use the t-56 bellhousing or do you want to sell it ?
I have a evo 3 and la coupe for my next build
Ps nice set up that you have there
Cheers stealth
Re: GH with a EVO ix 4G63 engine
Posted: Sat Dec 26, 2015 3:16 pm
by LSX
I might sell it, unsure at the moment. I don't know if the EVO 1-3 bell housing pattern is the same as 4-9
Re: GH with a EVO ix 4G63 engine
Posted: Sat Dec 26, 2015 3:21 pm
by stealth
Where are you located
And is the short shaft to suit t -56 out of commodore's ?, I have a vu ss box
And it should be the same just a narrow mitsi with the extra bolt
Cheers stealth
Re: GH with a EVO ix 4G63 engine
Posted: Sat Dec 26, 2015 3:27 pm
by LSX
Commodore runs the long shaft. I believe the ford has short input.
Located in Sydney.
Re: GH with a EVO ix 4G63 engine
Posted: Sat Dec 26, 2015 3:40 pm
by stealth
Hmm , still keen cant be to hard to change the imput shaft , or do you have the box to suit
Either way drop me a pm with a price that you want , if you're keen to sell it
Im sure we can work something out , no rush
Cheers stealth
Re: GH with a EVO ix 4G63 engine
Posted: Tue Dec 29, 2015 12:33 pm
by yno26galant
Very nice ! Keen to see more pics
Re: GH with a EVO ix 4G63 engine
Posted: Mon Apr 25, 2016 6:43 pm
by xTerraH
BUMP
Any progress?
Re: GH with a EVO ix 4G63 engine
Posted: Sun May 01, 2016 6:47 am
by 75wagon
I'd be keen to see some more pics of this
I'd also be keen to hear more about what's needed to install an Evo 9 motor.
Everyone here that I've seen seems to stick to the early Evo motors.
Dave...
Re: GH with a EVO ix 4G63 engine
Posted: Mon May 02, 2016 8:07 am
by stealth
75wagon wrote:I'd be keen to see some more pics of this
I'd also be keen to hear more about what's needed to install an Evo 9 motor.
Everyone here that I've seen seems to stick to the early Evo motors.
Dave...
Most people have opted for evo 1-3 vr4 as the blocks is narrow or wide and cheap enough to buy so to speak
Evo 4 onwards are more expensive and completely a different bellhousing pattern
The intake exhuast is reversed and has mivec
Would be a great conversion
Cheers stealth
