Remanufactured Clutch Cables

This section is for talk about anything to do with transmission or drivetrain.
Post Reply
User avatar
Sigmaproject
Posts: 1143
Joined: Sun Mar 22, 2009 7:11 am
Location: Maitland NSW

Remanufactured Clutch Cables

Post by Sigmaproject »

I just had a local clutch and brake business remake my clutch cable. Looks like they reused the adjustment mechanism and the nylon cable ends from my old cable..and used a new inner /outer cable.

Cost $130.00 which sounds a bit expensive..but the alternative is a piece of rope through a hole in the floor attached to the throwout arm.

Image
hengagc75
Posts: 261
Joined: Wed Aug 29, 2012 2:55 pm

Re: Remanufactured Clutch Cables

Post by hengagc75 »

Pretty sure Flexible Drive Agencies also make them for around 85.00
User avatar
LukeAussie
Posts: 353
Joined: Fri May 18, 2012 9:55 am
Location: Adelaide

Re: Remanufactured Clutch Cables

Post by LukeAussie »

Hi guys, yeah, Flexible Drive Agencies do this kind of thing (including re-working old gear if new ones can't be found), and also do speedo cables, accelerator cables, etc. Pretty sure they're in every state too...
User avatar
Sigmaproject
Posts: 1143
Joined: Sun Mar 22, 2009 7:11 am
Location: Maitland NSW

Re: Remanufactured Clutch Cables

Post by Sigmaproject »

I probably could have found cheaper options..but these guys were 5 minutes from home, and I had it back in an hour. :thumpsup:
Turbo047
Posts: 93
Joined: Thu Apr 19, 2012 8:45 pm

Re: Remanufactured Clutch Cables

Post by Turbo047 »

G'day Sigmaproject.

I've got a couple of new genuine cables with the screw adjust I could part with if you want a spare.
"Just remember, if you aren't forced induced, then you aren't SH#T"
GH Sigma Turbo no. 047

Leyland P76 V8 (next for resto)
Jaguar XJ8 Sport (british racing green of course)
Land Rover Discovery II V8 (the daily drive)
User avatar
Sigmaproject
Posts: 1143
Joined: Sun Mar 22, 2009 7:11 am
Location: Maitland NSW

Re: Remanufactured Clutch Cables

Post by Sigmaproject »

mate..if it is approx 1350mm tip to tip I will take one from you. This one I had made is actually my spare. I had a new cable I bought off ebay years ago to fit a GN Sigma and unfortunately it is about 50mm too long.
So I had to fit a 50mm spacers were it goes through the firewall to shorten the inner. Works OK ..but looks a bit dodgy. So if your cable is the right length I will take one.
PM me with your price.
User avatar
amgis_obrut
Posts: 1742
Joined: Wed Mar 18, 2009 6:26 pm
Location: Orient Point NSW

Re: Remanufactured Clutch Cables

Post by amgis_obrut »

I need to check if I have any NOS cables at my other shed, I had a few hundred of them and was selling them for $30 each
GH Sigma, 16" Mesh wheels, sports steering wheel and a V8 exhaust
User avatar
Sigmaproject
Posts: 1143
Joined: Sun Mar 22, 2009 7:11 am
Location: Maitland NSW

Re: Remanufactured Clutch Cables

Post by Sigmaproject »

The cable I am after is part #4158964
That is the GN part #. Maybe previous models have the same cable with a different part #. Who knows.
I'm guessing that the cable I bought that was too long was from a Triton or a Pajero (thats if they have cable clutches :roll: )
Post Reply