Search found 132 matches
- Sun Apr 26, 2009 3:09 pm
- Forum: Engine
- Topic: car keeps running on!!!!
- Replies: 54
- Views: 6091
Re: car keeps running on!!!!
did you make sure all the jets were tight and the float level is right.just to let you know my mates sigma was doing this and i fixed it buy the choke it was stuffed and carbon build up on the valves try wiering up the choke and using brake fluid down carby and adjust the fuel mix screw youll get it...
- Sun Apr 26, 2009 12:10 pm
- Forum: Engine
- Topic: balance shaft
- Replies: 4
- Views: 645
Re: balance shaft
all done started it and the timing cover is leaking water danm it now its gotta come off again gonna silicon the shit out of it hahaha thanks for your help 81 gl
- Sat Apr 25, 2009 10:30 am
- Forum: General/Technical Chat
- Topic: Workshop Manuals in PDF *NEW A51-GC Galant*
- Replies: 50
- Views: 30049
Re: Workshop Manuals in PDF
and where do you download them?
- Sat Apr 25, 2009 10:29 am
- Forum: General/Technical Chat
- Topic: Workshop Manuals in PDF *NEW A51-GC Galant*
- Replies: 50
- Views: 30049
Re: Workshop Manuals in PDF
can you tell me how to make them into a pdf coz ive got a tn tm factory manual here if any one wants it it cost about $200 buck its a awsome manual about 3000 pages though
- Fri Apr 24, 2009 11:19 pm
- Forum: Engine
- Topic: car keeps running on!!!!
- Replies: 54
- Views: 6091
Re: car keeps running on!!!!
just try it what have you got to loose its not going to stuff anything and try the flood with hand trick let me know how it works
- Fri Apr 24, 2009 11:14 pm
- Forum: Engine
- Topic: balance shaft
- Replies: 4
- Views: 645
Re: balance shaft
so that bearing just block the oil gallery? and you dont have to put the shaft back in?thanks for that i thought they only had one balance shaft lamo.and as i dont have a manual how do you prime the oil pump? vasaline
- Fri Apr 24, 2009 9:46 pm
- Forum: Engine
- Topic: car keeps running on!!!!
- Replies: 54
- Views: 6091
Re: car keeps running on!!!!
yes its fine i have done many of times
- Fri Apr 24, 2009 6:59 pm
- Forum: Engine
- Topic: balance shaft
- Replies: 4
- Views: 645
balance shaft
ok ive got the balance shaft out new chain on now the kit came with a stud with a tred in it and what looks like a cam bearing where do these go i think you need to cut the balance shaft and put the thred stud in and a bolt to block the hole am i right and whats the bearing looking thing for ?
- Fri Apr 24, 2009 6:40 pm
- Forum: Engine
- Topic: car keeps running on!!!!
- Replies: 54
- Views: 6091
Re: car keeps running on!!!!
sigma engines had a comon problem with exesive carbon build up on the valves what you do is you take the air clener of get a cople of capfuls of brake fluid hold the engine at 2000 rpm and tip it down the carby that should work also try hold the revs at 2000-3000 cover the carby with your hand it wi...
- Sun Apr 05, 2009 6:44 pm
- Forum: Engine
- Topic: Webber 32/36 jetting
- Replies: 10
- Views: 2564
Re: Webber 32/36 jetting
i would just chuck it on an see if its any good
- Sun Mar 22, 2009 7:54 am
- Forum: Members Rides
- Topic: GC Coupe
- Replies: 16
- Views: 3410
Re: GC Coupe
i have never seen a two door galant that is awsome what engine they come with 1600?
- Sun Mar 22, 2009 7:49 am
- Forum: Sigma's Section
- Topic: what else for turbo setup????
- Replies: 2
- Views: 918
what else for turbo setup????
ok want to build astron 2 2.6 turbo what ive already got. astron 2. from early magna carby new head over size pistons +0.25 astron 1. 2 liter this is what i know i need full rebuild balance cam turbo,turbo manifold dont know what rods to use? dont know what efi setup to use ie computer throttle body...