Sigma-galant.com

Yeah good luck. Took me 3 weeks to figure out out. Want to come over and take some pics? Are you running points?

Haha Yeh I hope it's timed right but probably worth checking! The shop installed it but may have not known how..

Make sure both carbs are working 100% properly. Have they been stripped & overhauled? Any air leaks ? You can't reasonably expect a set of old carbs to just bolt on & be fine. Carbs are brand spanking. All sweet. Im going to try fiddle with a few things next week, thankyou for the effort in...

Quick one. Will Weber DGAS jets fit? I just fixed my 38/38 as it was running 0.2mm larger main jets on a 4g54. I bought heaps of different jets so might just start by giving up one size after I check the secondaries Yeh when I took to get my carbs rebuilt they quoted 1k plus Coz they just didn't wan...

Thanks. I haven't got any money as just got back from a few months in Europe so pro tune out of the question. Might see if can find a mate with a wide band and a carby air flow thingy. I will test the secondaries, I did think this actually, especially as with the Less Vacuum they would open at highe...

Hi Hi.

Can you get kits to change the dizzy to a fixed sensor and fit a throttle sensor and run a fully customisable ignition program?

I dont know where to begin researching!

Hi team. After trial and error error error, I need some advice. Imagine you have the following: 4g32 bored out 1.5mm Standard pistons because the builders bored to much for the 1.0 flat tops Beamed forged Rods and arp all round Double valve springs Number 5 original works cam Twin down mikuni setup ...

Just make sure the front to rear ratios are the same!

Damn.

Where in Perth are ya?

The problem I had with this is I used a short dipstick in a higher hole. So it tells me to put a lot more oil in. Not good

Yes overheats on freeway sometimes. When is hot anyway

No. But winding the timing back helped a little

http://www.ebay.com.au/itm/56mm-3-core- ... 3a7cd95148

i use that

Hk works well for me. Only issue si you need two hose sizes

what rpm do you idle at dave? do you know what jets you have in? My carbs were freshly rebuilt and all stock jets I have davies craig suck through, but is not ducted between ac and normal rad. The temp has reached 100 as the electric switch is a 60-100 actutor and i once cranked it to 100 and i didn...

Yes i know that. The dizzy needs to be recurved. Cant get it to work with the stage 5 very well its a pain in the ass. Wont idle at low rpm with the timing retarded and then pings when advanced. Its shit

by burped, usrely if it has heated and contracted a few times all the air would be gone?

The water pump was brand new

Not what i wanted to hear.

Thanks brugs.

It is running lean though. Pings under load below 3k

I will check coolant flow..

My guess is yes, airflow. Idle it does not overheat as the davies craig is just sucking air. But on the freeway with the a/c on it slowly cooks. Even hot days with a/c off on the freeway it gets hot. The engine is freshly rebuild and acid dipped with new welsh all round, the rad is a HQ V8 alloy 56m...

Thanks Dave. From the pipe that wraps around the engine, one goes to the heater core and then to the pipe that comes out the back of the head, and the other i have split and fed to each carby water inlet. Is this correct? If so then I will check the thermostat, and then I will have to just try and b...

Anybody that has a 4g32 and stock twin down carbies, I need help with my coolant hoses. I'm overheating even with a hq alloy rad which only leaves a couple of options. I'm not sure if I have my hoses the right way.
Any help would be awesome

Are you going to be putting the pin striping/decal back on the car since it is now resprayed? I have to replace the front fenders as i used 2 off my coupe as they were the best nic ones i had, and they dont fit properly. After that i will. But that will be after i get back from europe. builds comin...

Runs well, but only done 700km. I'm going to do a few more km before I test her. Idles mean as, and i have timing set at 20 degrees static, but i need to have dizzy recurved because i cant sit on any less than 80 in 5th without pinging. Could also have something to do with it being a #5 cam too! Pic...

Fouling as in the plugs are white, black, or just buggered?

Yeh just have so many other more important things happening ya know

Ive ordered a s13 tripple core. See how that goes

Wrong temp plugs?

My guess is you have the ballast resistor on the wrong place. Or not on at all?

Here are some befor and after shots of my car, followed by some recent shots showing current state for those of you who may care. https://fbcdn-sphotos-b-a.akamaihd.net/hphotos-ak-prn1/38474_446455275398_3815033_n.jpg https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-ash3/12557_10151312930585399_161...

Hey team. WA Chrysler Expo coming up in Jan and i plan to be there representing us as a body. For anyone who actually cares where im up to after 30 months of slow work, there are some pics below, or you can visit the whole album in my signiture for the whole build. Work completed: EXTERIOR Full resp...