Sigma-galant.com

Welcome mate

That thing looks like a cross between the 1st gen hyundai excel, with a cordia front it's cool!

Don't worry, I'll be out there rocking the s-g stickers once my old girls done

Ah righto

So, the original pic posted. Is that just the inside half of the caliper??

Thanks guys!

And maybe tomorrow...

Wait, no... I need stuff! Hmmm, mind the check list

Engine? Check

Battery? Check

Fuel? Check

Cooling stuff (rad, hoses, thermostat etc)? Hmm... Check

Gaskets? Yep...

Anything else?? Again, sorry for the check list.. It actually helps lol

Hmm... I'll jack the scorp up tomorrow and take some pics... Pretty sure they're a large setup like the sigma/commodore

They're weird

They're not galant/sigma (except gd and ge, I have no idea what they look like)..

Just checked out gh scorp. They look close to my gh sigma calipers on my gb...

So I'd have to say, I have no idea. But they're not gh scorp

Cheers haha

TADA!!! :D First time the two have seen each other in a while :) http://sphotos-c.ak.fbcdn.net/hphotos-ak-frc1/t31.0-8/10012685_823701407646353_1641830355_o.jpg A detail shot :) http://scontent-b-lax.xx.fbcdn.net/hphotos-frc1/t31.0-8/10003567_823702280979599_377454894_o.jpg And THIS!!! :D http://sco...

If it rains, open up the drain plugs in the floor (assuming u have no carpet in it) and ull be able to drain the water a bit more effeciently Yea there's no plugs in it, but there's electricals behind the dash, and where the back set goes doesn't have a drain hole... I'd rather not put her out in i...

32/36 webber carb.. Some extractors and a 2" exhaust. And a very mild cam should be enough

Thanks mate :) Yea I was gonna buy a new clutch while its out.. But this ones new enough so fxck it :P Got oil and filter, gotta clean up the engine mounts as I painted em.. Tidy up the accessories (alternator, starter, etc). Mate the box back to the donk, paint the tailshaft, and she can go in! :D ...

I've got a billet 30/70 in my 1600 from Peter waggot nice and lumpy

Cheers

All these little things I'm doing will add to the entire finish of the car.. So mind the fiddling around painting small insignificant crap you'll see when it's together..

I MAKE STUFF PRETTY!!!! :D Before http://photos-e.ak.fbcdn.net/hphotos-ak-ash3/t1.0-0/1911822_820837207932773_13846983_n.jpg After http://photos-b.ak.fbcdn.net/hphotos-ak-frc1/t1.0-0/1912469_820837491266078_875423768_n.jpg Before http://photos-f.ak.fbcdn.net/hphotos-ak-prn2/t1.0-0/1382865_820839191...

Cheers mate

I'm hoping she will fill my expectations of being one of the tidiest galants built

On this episode.... THIS!!!!! :D http://photos-a.ak.fbcdn.net/hphotos-ak-ash3/t1.0-0/1932209_820392644643896_1897387136_n.jpg http://photos-b.ak.fbcdn.net/hphotos-ak-prn1/t1.0-0/1960004_820393257977168_462926762_n.jpg And have her a bath! :D This is how she sits now :) http://photos-g.ak.fbcdn.net/h...

What about one that follows the body line from the rear door forward? Much like the sports pack striping

And I followed Pete.. Down the the part# he used.. Except brake pads. And I haven't got around to shocks yet... Now I know ;)

But I have no issues in a gb galant... Using all factory parts minus the strut, caliper and rotor. Will need to use the gh brake cable from the body to the caliper

I don't have photoshop anymore lol

I might get it though, gotta do one for my car as well before I spent $2500 on wheels

Nah they're super lows, that were cut

Few small updates :) Got my brake calipers back. Completely rebuilt! New pistons, new pads (supplied by me), new bleeders, new seals :) http://photos-b.ak.fbcdn.net/hphotos-ak-prn2/t1.0-0/1798046_815733875109773_401763911_n.jpg And finally fit my sway bar with my new rubbers and refurbished link pin...

Oh ok then cheers!

fark me!!! Now that's a good job

I'm gonna do this for all my joins now, and solder the wire into the joiner

Nah stuff all mate! Did mine in less than half hour. That's from running with the 32/36 webber. To running with the twins. You will need to cut your top rad hose, and block the water port at the rear of the block. Also I forgot to ad!! I have race linkages on mine which means they pull from the top....

Well... First up, if the staz is IRS. Then you'll need to install a cradle into the lancer to hold the diff in. Then you'll have to put strut tops in the rear to house the struts that come with the IRS diff. Just that alone is some major mods! If its not IRS. Then I suppose it won't be too hard. Lik...

Looks same as mine dude :) so I'd say yes. Does it have "GALANT" printed on the top? Also, is it a LYNX manifold? As for carbs that fit... I guess so, this is what's needed for at least the dhla40 dellortos (that's what I'm running). Then the 45s aren't much different. Dellorto carbs and w...

Top ones a Saturn.

Bottom I'm not sure

Is the wire on the coil on there good? May have bumped it replacing the dizzy cap, and now it's come loose again?

It's on the negative ( - ) side of the coil

Yea the movie itself is really stuffed! Makes me angry actually lol..

But the sticker... I love it