Sigma-galant.com

Also block off the return fuel line.Ive run my car like this for about 15 years and its been fine.

Sorry to take so long to answer but Ive been away.I found that for traffic/daily drive .....primary ...idle 50..main 110..air 210,secondary...idle 70..main 115..air 190.Ive experimented with the main jets in both circuits all the way up to 150 for me its just too rich.THis carb on an 1800cc engine r...

Im searching for the wiper linkage nylon pivots,especially the one off the wiper motor end for my LA 1974 LANCER.Any options or alternatives. Im trying everything at the moment but original would be better.

I have one on a 4g32b motor.I may be able to answer some questions.

KYB gas inserts EXCEL-G 365046 74-77 models.I have them in my LA just make sure you have the tool to remove the holding nuts.

After searching the internet for a while with no success I turned around and lo and behold in my own library I have a PAYEN Japanese oil seal book which lists all the seal sizes.So KM132 gearbox front seal size is 25/35/6 Mitsubishi part no. is K613229-2.Rear is 32/48/8 or 10 ,K615323-2.These seals ...

I just blocked it and no probs.

Does anyone know the size of the front seal?

Do you have the size of the front seal?

On again At Glenelg 10am MARCH 15TH Sunday Alljapanday.com.au

Try Part no. MD701577 at your local Mitsubishi dealer.

The SP manual series 162 has pictures on pages138 and 139 of the wheel and boss and horn contacts.If you have an email I could scan and send them to you.

The rubber companys like Clarke rubber have a cross section listing.I compared my LA and it came very close to a Torana which model I forget, anyway the holes for the locking clips needed to be re cut and the length has to be precise.Joined it with superglue and it worked great.Had it on for 4 years...

If the 4G15 starter fits that is a Bosch BXM002.The dimensions are in the Bosch catalogue.

This photo thing is new to me

Sorry new at this will try again

Some photos from Malalla http://i252.photobucket.com/albums/hh35/normanr/Malalla/SANY0126.jpg? http://i252.photobucket.com/albums/hh35/normanr/Malalla/SANY0124.jpg? http://i252.photobucket.com/albums/hh35/normanr/Malalla/SANY0122.jpg? http://i252.photobucket.com/albums/hh35/normanr/Malalla/SANY0127....

Do you still need a wiring diagram?

Lee in Adelaide LA4door 1974.My wife bought it in 1984 and gave it to me in the late 90s and ive played with it ever since.Has a lot of extras but looks mostly standard.The advantage in SA is no yearly rego check.

Cutting and glue to correct length is very easy also re cutting holes to line up with the old mounts.I have Torana rubbers on my LA 4 DOOR and they fitted fine.Took me about half an hour doing it carefully.

You can get most things done if you have the money.Engine can be adapted machined retro fitted, clutches, exhausts,suspension,fuel systems it just depends how far you want to go.Have a look at Hoonboy to see what is possible.

I have a 4G32B 1600 motor in my LA with 5 speed, bolted straight in.It was all removed from an LC including the complete rear end The only thing I had to do was match the drive shaft and remove the dust cover from the shaft/gearbox end.There are always small lining up fiddles but nothing major.The m...

I had so many little problems when trying to fit and run an electric pump on a day use car that I spent the $72 and went back to a mechanical. It took 5 mins to fit and the car runs perfectly.Lesson learnt.

For Weber reco kits try TURIN IMPORTS in SA they have a web site.I just got a kit for my 32 DMTR 22 $57.00 all gaskets ,orings needle and seat.

Cams for 4G32B ARE FOUND ON WEB SITE http://www.camtechcams.com.au/ hope this helps ---

DBA do slotted discs for just about all the old Mitsis

Im very glad to help.This site has helped me many times and its good to return the favour

PART NUMBER for plastic gear change bush is MD701577 it should be still a valid number.

The only other thing is I had to file /grind the bracket where the exra hole was drilled so I could hold the nut to tighten it.I couldnt see any other way to do it but again it was only a minor problem.Yes I was very suprised it lined up so well.If your in Adelaide I got it from Nisswreck in Wingfie...

Im sure I only drilled one hole its been a few months and I had to rely on the model hand written in texta .Knowing how wrecking yards are run it could have been from a different model.If the dimensions are ok drilling one or two holes is a minor problem clearing the air cleaner and clearance to the...