Sigma-galant.com

Ok well I replaced the reg and the alternator is still not charging, I have double checked the wiring the wiring from the light and it has good connection and is giving a positive feed I have tested the battery wire and tested the the battery sense wire(blue) on the plug and they are all giving good...

I have charged battery to full capacity on my c-tek charger, and it reads 12.8v, after I start car and run it with thermo fans off it sits on about 11.8v and slowly drops. If I put thermo fans on it drops quicker, I have pulled reg out and measured ohms across slip rings on armature and I have 130.k...

Ok I have tested the charge across the battery with the engine running and it is reading 11.2v this indicates I the alternator is not charging, I tested the circuit with a multimeter across the connection from alternator wiring(magna loom), and the plug from the lancer and I have a positive charge a...

Is there a way if testing the reg to see if it is faulty? Are they overly sensitive? When removing engine and installing it the alternator may have been bumped but nothing major, the usual taps against radiator support panel that happens as an engine is craned from and into a vehicle, I also swapped...

The blue wire was wired straight to power when it was in the magna so I have put it straight back onto power in the lancer, the white wire has been run to the yellow wire in the lancer's reg plug, this is the only wire in the loom that triggers the light, when this where is disconnected there is no ...

That is what I have done but it isn't charging, the light comes on but won't go off when engine is running, the alternator was working in previous vehicle and my charging system was working

I have fitted a tn magna engine into my la lancer and all is complete except the alternator wiring is giving me trouble, I have used the magna alternator which is a Bosch style with regulator mounted on the rear of the alternator, I have removed the external reg from the lancer alternator setup (box...

I have fitted a tn magna engine into my la lancer and all is complete except the alternator wiring is giving me trouble, I have used the magna alternator which is a Bosch style with regulator mounted on the rear of the alternator, I have removed the external reg from the lancer alternator setup (box...

I have removed the head off my 4g52, the head has a lot of corrosion, I noticed there is small valve looking things that fit in beside the spark plugs I haven't seen this before, also there is a water gallery that runs along the head on the exhaust side, this also is new to me, is this a common head...

Ok thanks, well I won't know what I will do exactly until I pull the head off, the only other solution might be to obtain a complete magna engine and convert it to rear wheel drive using the timing cover, water pump and sump setup.

Will a head from a efi magna (astron2) with the efi setup fit onto a 4g52, will it work with the efi? Will I have compression problems? I have 4g52 in an la lancer and the head is a bit ordinary, I also have an la lancer with a turbo charged astron2 with tr magna head and injection, I know how to fi...

i have gt35r on astron 2 .7 front .82 rear on 27psi it makes solid boost around 2800rpm and full boost at 3200rpm. lag is non exsistant feathering throttle in anything under 4th gear or it just smokes the tires. makes 380rwhp and my tuner thinks i should have got the 1.06 rear housing would be smoot...

hello fellow sigma owners. i live in brisbane and require the loan of a flywheel to measure up so i can make a billet flywheel for my car. the flywheel will come back in same condition as loaned to me and will not be fitted to a vehicle or damaged in any way. it is quite urgent that i get a loan of ...

i have master cylinder from proton satria i will fit it to same place as yours i might get the same master as the one you have though it looks morte heat resistant mine has plastic resivor. is that the master they sell for hydralic brakes on boat trailers? is it 3/4 sleeve? looks like the one i put ...

im looking for a 2.6 manual flywheel to use as a template to make up a new billet flywheel for my rb25det gearbox conversion into my lancer.

im located in brisbane any help would be appreciated, thankyou.

tim 0411344827

It has been a while since i updated about this build. after breaking another supra box i decided to change gearboxes. i originally thought to go automatic with transbrake but lots of enqiries with people left me with no answers, $800 out of pocket with a transbrake kit that wont resell and totally f...

Lancer in Car <-- 12.00 @ 123mph

380rwhp on Dyno

i have a 1974la 4 door dark green with grey vinyl roof that i built up over 3years. it is running astron2, gt35r turbo 27psi, w58box, borgwarner diff 31spline axles, fullspool. it makes makes 380hp@wheels, only runs 12.03@123mph haven't run a proper pass yet as it keeps breaking. my missus put photo...

the locating pin on cam was stuffed and hole on cam gear was damaged so we repaired that and made solid pin to press into cam. the hollow dowel pin collapsing is what caused all the damage. i got to run lancer at willowbank last wednesday night, first run i pulled 12.04@119mph, i was shifting at aro...

just a bit of an up date for my lancer, i managed to chase down a group of people that were getting a multi-layered steel head gasket made up for astron engines made by cometics usa, but after they got stuffed around for about 8 weeks with no further progress i dropped that idea and purchased a .60t...

i took the lancer for dyno tune on the friday and the intake manifold gasket started leaking between runner one and coolant port so when it came on boost it pressurised the cooling system. i fixed that and decided to check tension on head studs because i hadnt torqued it down for the second time. i ...

finally the lancer is at a point where i would say it is completed, (for the time being anyway). its booked in to get dyno tuned this friday, and if all goes well i will probably run it at willowbank on wednesday 29th of july.

hey nice lancer. im currently going to efi and wondering what throttlebody you are using? obviously you have a custom plenum byn the looks of things but the bottom half of the manifold is jus a Tn magna item? im using throttlebody off ls1 holden(chev) it measures 75mm butterfly. custom plenium whic...

i haven't run this car yet so im not sure what sort of time it would do, im hoping low 11s maybe better. i was planning on running it at willowbank next week but i may have to put that on hold as i blew head gasket in daily driver which will consume my funds for a little while. the car is nearly com...

http://forghani.net/forum/files/lancer08_661.jpg http://forghani.net/forum/files/lancer09_154.jpg http://forghani.net/forum/files/lancer102_147.jpg http://www.forghani.net/forum/files/coilover_131.jpg http://forghani.net/forum/files/lancer02_172.jpg http://forghani.net/forum/files/lancer03_182.jpg ...

i dont know how to use computers to put up pictures, i will see if my girlfriend knows how to do it.

there is footage of the car on youtube, the names are on my first post.

im currently building a 1974 la lancer, the build has taken just over 2 years to get to this stage and it is almost finished. astron2 m6 head, wiseco 4g54b forged pistons, argo rods, knifebladed polished and balanced crank, garrett gt35r, 38mm turbosmart ext. gate, custom grind shaw cam, adjustable ...